Waterproof Wind Controller for 2000W 48V AC Turbine Generator | Обустройство дома

Waterproof Wind Controller for 2000W 48V AC Turbine Generator | Обустройство дома

Waterproof Charge Controller for 2000W 48V AC Wind Turbine Generator  2000W Wind Turbine Generator Controller 

Waterproof wind turbine charge controller instructions for use  

1、Features:

 The controller can control wind turbine automatically charge the battery. In the case of the battery is filled, through the internal circuit automatic control so that wind turbine brake, when the battery voltage dr ops to the voltage recovery, wind turbine resume charging the battery so as to protect wind turbine and battery.

 The charging pressure limiting current limit control to ensure the best charging results, provide maximum protection while on the wind turbine and battery.

 The automatic brake and manual brake complement each other, to meet the different needs of customers.

 The unique reverse polarity protection circuit. Battery reverse due to improper operation will not need to replace the fuse, the positive and negative polarity reconnected correctly (This feature has won the praise of customers), the entire system run more reliably.

The indicating circuit status light-emitting diodes, simple, intuitive and clear.

The modular design with independent intellectual property rights, the performance of the entire system to get the maximum protection. Rectifier and brake circuit part of the controller, using the integrated module design, both from the heat, or reliability, further than the traditional design.

 The comprehensive waterproof protection. Not waterproof controller in 2012, controller board will rust if you use high humidity, or seepage easy environment, the controller is more susceptible to corrosion corrupted, increase the after-sales service of Contractors the workload, and even easier to lose customers. This subsection, the controller uses a fully sealed completely waterproof design, no longer have to worry about the environment, air humidity, salinity, ground water and do not have to worry about the controller water after a short circuit burned, protection grade IP67 above, even if placed in the water is also a long-term normal use, substantially increase the stability and reliability.

 The controller selection of imported electronic components and industrial-grade chips, key accessories using military grade product, has a high stability performance of the entire controller. The company has ISO9001 quality management system, products strictly in a variety of aspects of production, testing, quality has been the greatest degree of protection products can guarantee stable at -35 ℃ ~ 70 ℃ high and low temperature environment for long periods.

  2、Note:

⑴. Confirm consistent wind generator output voltage and rated voltage of the battery.

⑵. Following order wiring connected to the battery's positive and negative, were followed by the three-phase voltage output fan.

⑶. Carefully follow the instructions require batteries and wind turbines connected to the controller, reverse polarity, or take the wrong position will cause the system is not working properly, or even cause damage to the system components.

⑷. Although the controller has taken protective measures for a variety of unexpected situations that may occur, but is still strongly recommended that strict adherence to rules, to prevent causing tremendous damage to the battery and controller.

3、Connection mode:

Ⅰ. Be respectively connected to the battery "and" - "to the controller of the battery positive and negative terminals.

Ⅱ. The three-phase output voltage of the wind turbines are connected to the three-phase voltage input terminals of the controller fan. And

Ⅲ. When the need to manually brake red thread short battery positive then, to complete the manual brake function, cancel this function, simply disconnecting the thin red line.

4、Indicator status:

The controller green power (BATTERY) indicator light indicates normal battery access.

The controller the green fan access (WIND) indicator flashes, indicating that access to wind turbines, flashing the speed of the fan speed level.

The controller red (BRAKE) light is on, the battery is full, wind turbine automatic brake, or due to the over-current protection automatically brake, or is in a state of the manual brake.

Type

FW-20-48

Battery Rate Voltage

48V

Wind turbine Rated Power

2000W

Brake start voltage（Default value）

60V

Brake recovery voltage（Default value）

54V

Display

LED(Light emitting diode Display)

Operating Temperature Range

-35℃-75℃

Controller Shell Size

150mm*132*48mm

Quiescent Current

≤20mA

Protection class

IP67