LED Модуль освещения лестницы с датчиком движения и контроллером 36 каналов 12V 24V гибкая цветная полоса RGB CW WW Step Staircase Lamp Running on

LED Модуль освещения лестницы с датчиком движения и контроллером 36 каналов 12V 24V гибкая цветная полоса RGB CW WW Step Staircase Lamp Running on

LED Motion Sensor Stair Light Strip Controller 36 Channel 12V 24V Flexible Pixel RGB CW WW LED Strip Step Staircase Lamp Running

1.The controller has two human-sensing device interfaces, which are marked with Sensor Connection at the top left of the picture.

2.The right side of the marked Sensor Connection is where the product is connected to the power supply. It has two power supplies with positive poles and two power supplies with negative poles. When you connect, you must connect either of the positive and negative poles at the same time to make the device work normally.

3.Next are the ports of the Arabic numerals 1-36. They refer to the number of your steps. If your number of steps is only 10, then you only need to connect the 10 ports 1-10. Just adjust the data of the device (there will be adjustment instructions below). If you have 15 steps, then connect the light bar to the area 1-15. By analogy, if there is 36, then you can perfectly connect to ports 1-36. If you have more than 36 steps. You need to purchase a second device to complete your renovation. The picture says Connect to Warm white or Cold White Led Lights (First Floor) and Connect to Warm white or Cold White Led Lights (Second Floor) are the positions where the light strips are connected to the monochrome stairs.

4.The light bar connected to the place marked "Connect the addressable Led Strip" is the water light bar on the wall of the staircase. It has two ports, "OUT1" and "OUT2" respectively have 3 connection ports, and "DO" is connected to the pixel dot Signal line. "GND" is connected to the negative wire of one outlet of the signal wire. A total of two ports can be connected to a 12V 2811 light bar with a pixel point of 40 meters (100 pixels per 5 meters of light bar). The two ports can be connected to a total of 800 pixels. You can connect the light bar according to the number of pixels of your light bar.

5. The four red buttons on the device, "—" "+" "MODE" "SET". They are to adjust the number of steps controlled by the equipment, the lighting and extinguishing speed of the light bar, the color selection of the light bar on the side of the stairs, the length and speed of the flowing water. These four buttons are required to cooperate to complete.

Features:

36-channel multi-function LED staircase controller with two sensors, which can drive 2 kinds of LED strips, one is a strip that supports a single-line chip via SPI, such as general-purpose 1903, 1812, 16703 WS2811 and other full-color pixel LED lights, the control system is in the lower left corner of D01, GND, DO2, and GND have two parallel output terminals, which can be connected to the left and right sides of the staircase light. The output terminals on both sides of the controller are 36 monochromatic light strips , The number of light strips is adjustable, the function setting of the sensor controller is selected by the button, and the setting is displayed by the left 4-digit digital tube.

Specification:

1.Working Volatge:DC12-24V.

2.Output Current:2A*36CH.

3.Step Numbers:36 Seps Max.

Connection Diagram:

The entire set of equipment requires a suitable power source. You can choose a power supply with higher power to prevent the light bar from not working properly due to too low power. The number of light bars is selected according to the number of steps. If your step length is 1 meter and the number of steps is 15, it is recommended that you buy 15 light bars with a length of 1 meter and connect them to ports 1-15. The indicator light will light up from 1-15. Choose how many steps, the display lights will light up the same number of lights. After connecting the two sensors to the device, they need to coordinate with the data set in the device to adjust the installation position. One is installed on the stairs and the other is installed on the stairs. Light bars with pixel points are usually installed on the wall on the side of the stairs. If you want, you can also install it on the railing of the stairs.

Screen Data Adjustment:

1. After the equipment is energized and stable, the data displays "10-L", and then press "SET" in the first step, and the screen displays "L036". This number means that the number of steps is 36. You can adjust according to your number of steps and press " -" This button is reduced to the number you need. Then continue to press the "SET" button.

2. Press the "SET" button for the second time, the screen displays "LP01". This data adjusts the color of the water light bar on the side wall. If the light bar connected to "OUT1" or "OUT2" is full-color 2811, 01 is white, 02 is red, 03 is green, 04 is blue, 05 is Yellow, 06 is purple, 07 is cyan. If your light bar is a single white light or warm white light, you can directly press "SET" again.

3. Press "SET" for the third time to display "LH10", press "-" to increase the flow rate, the fastest is "LH01", press "+", it is slow, and the slowest is "LH99". You can adjust the speed of the side water light bar according to the time you climb the stairs, and adjust it to the same speed as you accompany the stairs or descend the stairs.

4. Press "SET" for the fourth time to display "F036", which refers to the pixel point of the light bar on the side wall of the staircase. "036" represents 36 pixels. Use the "-" and "+" buttons to adjust the pixel point Number, up to 800 pixels can be set. Choose the pixels you have.

5. Press "SET" for the fifth time, the screen is "FP01", this data is the mode, it only has two choices of "FP01" and "FP02", just select "FP01". "FP02" has not yet added a program to the chip, so the device cannot be used yet.

6. Press "SET" for the sixth time, and "FH10" is displayed. It is the speed at which the stair step turns on and off one by one, and the speed at which "FH01" turns on and off is the fastest. The maximum can be increased to "FH99", which is the slowest speed. Adjust by "-" "+".

7. Press "SET" for the seventh time, it is "E001", it refers to the length of time that the light bar above the steps lights up as a whole, from "E001" to "E255", the shortest is 1 second, the shortest The length is 255 seconds. Choose how long you need to turn on the light bar. Use "-" "+" to adjust.

8. Press "SET" for the eighth time, and it will be displayed as "AA20". It needs another product to match and do more settings. At present, we have not listed the equipment that matches it, so we only need to adjust it to " AA01" is fine. It is also adjusted by "-" "+".

9. Press "SET" for the ninth time, all the adjusted data in front of it will be saved in the device. When you turn it on next time, it will still be the number you set. If you need to adjust any of the data, press the "SET" key, select the corresponding place that needs to be changed, press "-" "+" to adjust, and then press "SET" until it returns to "10-L". Then the next startup will be the last time you adjusted the data. If you don't want to save the last adjusted data, please turn off the power directly. It will not retain data.