WS2815 30leds/m RGB Dream Full Color Smart Addressable Pixel LED лента + SP108E WiFi контроллер + 12V набор питания 5м-20м.

WS2815 30leds/m RGB Dream Full Color Smart Addressable Pixel LED лента + SP108E WiFi контроллер 12V набор питания 5м-20м.

Wide compatibility:
Can be controlled by Arduino, Raspberry Pi, Fadecandy, K1000C, SP105E, SP107E, SP110E etc.


12V WS2812B LED Strip:
WS2815
LED strip is upgraded version of 5V WS2812B LED strip. For 5M LED
strip, even if all the LEDs are turned on full white, 12V version has no
voltage drop. You don't need to inject power as frequently as 5V
version.


Individually addressable:
Each
pixel can have its own color and brightness. You can control it
individually and set them to any color or animation you want. 256
brightness display and 24-bit color display.


Dual-signal wires:
WS2815
LED strip is Similar like the version of 5V WS2813 LED strip, Designed
with one data wire and one backup data wire. Signal break-point
continuous transmission. If one LED is damaged, the following LEDs can
still work.


Easy installation:
Self-adhesive
tape on back FOR IP33/IP65, it can be fixed on any dry and flat surface
without any screws and clips. Each LED can be cut off at cutting line.
There
are 4-pin JST SM connectors and separated power/ground wires on both
ends, which make it easy to hook up each other and wire up for power.

Specifications:
IC type :WS2815 IC
Gray level: 256
View angle: 120°
Input voltage: DC12V
Color: full color 24-bit
FPCB board color: White/Black
Power: 0.3W/LED 30/60 LEDs/m
Model: WS2815 strip 5050rgb chips
Storage Temperature:-30-+95 °C
Operating Temperature:-20 ~ +85°C
Led Qty: 30/60 pcs RGB SMD 5050 per meter
The distance between two LEDs:30Leds/m -- 28mm, 60Leds/m -- 12mm
Wave length(nm):Red,650nm ; Green,520nm ; Blue,460nm
Waterproof level: IP33: Non- waterproof, IP65: Waterproof in Silicon Coating, IP67: Waterproof in SiliconTube

Package includes:
1 x led strip
1 x 4pin connector

Note:
1, The led strip must use with DC12V Power adapter and WS2815 pixel controller.

2, The Power adapter and controller are not included! If you need, please visit our store!

SP108E WIFI LED Controller OperatingInstructions

Certificates: CE, RoHS;

Note:
Can not use 5.0G WIFI network , it just support 2.4G WIFI network

AP (Access Point) mode:
Controller and Phone connect directly, controller works as an access point.
Connect steps:
When
the device is not connected to any WIFI network, power on the
controller and wait for 20s and then controller will switch into AP
mode;
In the WIFI setting page, find and connect the controller (named likeSP108E_xxx, the default pin code is 12345678),
Open the LED Shop App, then the controller will be showed on the device lis

STA (Station) mode:
Controller and phone are in one same WIFI network, in this network, users can operate the controller smoothly.
Connect steps:
When
the device is not connected to any WIFI network, power on the
controller, controller will be remain in Wait-For-Connect mode for 20
seconds;
Make sure that your phone is connected to a WIFI network,
Open LED Shop APP, pressing the Add Device button, input the WIFI pin
code, then press the OK to confirm and wait for the configure processing
finish;
When controller successfully enter the WIFI network, it will be showed on the device list;
User
can select the controller and remove it out of the network by pressing
the Remove Device button, then the controller will switch into AP mode.