1 Pcs LilyPad Coin Cell Battery Holder CR2032 Mount Module & 1200W DC Converter Boost Power Supply | Обустройство дома

body { font-size: 75%; color: #000; font-family: Open Sans,Arial,Helvetica,sans-senif,SimSun,"宋体"; line-height: 1.3; } dl { margin: 0px; width: 480px; float: left; } dt { width: 100px; height: 15px; float: left; } dd { width: 240px; height: 15px; float: left; } dl dt { margin: 0px; line-height: 22px; color: #474747; font-size: 14px; font-family: tahoma; } #product-desc { width: 100%; height: 209px; } #description { width: 100%; height: 50%; } #details { width: 100%; height: 50%; } .ui-box-title { height: 30px; font-size: 15px; font-family: tahoma; font-weight: bold; background-color: #ddd; text-anchor: inherit; padding-top: 8px; margin: 0px; } .ui-box-body { margin: 0px; } #tbspecifics { border-right: 1px solid black; border-bottom: 1px solid black; } #tbspecifics tr { height: 30px; } #tbspecifics td { width: 100px; border-left: 1px solid black; border-top: 1px solid black; }

1 Pcs LilyPad Coin Cell Battery Holder CR2032 Battery Mount Module & 1 Pcs 1200W DC Converter Boost Power Supply Module

Please be kindly noted，the listed product is produced and distributed abroad and subject to the laws of its country of origin.

1 pcs CR2032 Battery Mount Module & 1 pcs 1200W DC Converter Boost Power Supply Module
Power supply with double iron silicon aluminum 4 1.2MM pure copper wire and rao. 100V/210A low resistance power MOS, high power and high current input, suitable for high power LED motors.Have input MOS meter protection, don't worry about input after burn out the power supply.With over current protection and short circuit protection.Thickening of the radiator and ligent temperature control cooling fan
Note:The circuit structure of the booster module can not be adjusted by way of short circuit.The product of input power supply voltage must be above 8V.When the power supply is used for the input power supply, the input power and the output voltage of the input power supply are the first to be unloaded. Then pick up the load.(must ensure that the switching power supply has been working).
When the constant current mode is used to set the voltage, the constant voltage must be higher than the input voltage.Do not use the way of short circuit output current, the circuit structure of the boost module can not be adjusted in short circuit way.If the input voltage fluctuation range is lower than the set output voltage, then the output voltage is constant, it is to ensure that input is lower than the output voltage.

Material:CCL
CR2032 Battery Mount Module:
Colour:purple
This LilyPad Coin Cell Battery Holder has a small slide switch installed on the board, in-line with the power so you can shut off your project and save batteries
This slide switch is the same as is found on the LilyPad slide switch board, so it's not easy to accily turn off or on
Just like the original Coin Cell Battery Holder, this simple board holds a 20mm coin cell battery (such as a CR2032) and gives you 4 connection points (two positive and two negative) for sewing into your project
1200W DC Converter Boost Power Supply Module:
Conversion Efficiency: up to 95% (efficiency and input/output voltage, current, pressure related) Installation: 4pcs m Screws
Input Voltage: 8-60V
color: red
Input Current: 20A
Quiescent Current: 15mA
Output Voltage: 12-80V Continuous Adjustable
Output Current: 20A MAX. over 15A, please enhance heat dissipation (input and output pressure related, the greater the pressure, the smaller the output current)
Constant Current Range: 0.5-20A
Output Power = Input Voltage x 20A, e.g.
Working Temperature: -40 to 85Degrees Celsius(ambient temperature is too high, please enhance heat dissipation)
Working Frequency: 150KHz

Package Contents:
1 x for Arduino LilyPad Coin Cell Battery Holder CR2032 Battery Mount Module
1 x 1200W DC Converter Boost Power Supply Module

Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.